| 3 Aug 2023 |
 Alex | In reply to @fgaz:matrix.org
Nope :-/ RIP, guess I'll have to try more things. It might just be that I'm missing modules in initrd (which would imply the module dependencies are broken). | 22:14:20 |
| Alex | In reply to @raitobezarius:matrix.org
but isn't vs_drm a VeriSilicon GPU thingie? It is a Verisilicon thing, but it seems to be needed for DRM/HDMI (JH7110 has a DC8200). | 22:23:24 |
 raitobezarius | I see | 22:26:07 |
|  [0x4A6F] changed the room topic to "NixOS on RISC-V
https://pad.lassul.us/NixOS-riscv64-linux
" from "NixOS on RISC-V". | 23:04:22 |
| 4 Aug 2023 |
| raitobezarius | am I the only one with traces like this for NVMe ? | 00:24:40 |
| raitobezarius | [18795.121243] nvme nvme0: I/O 868 (I/O Cmd) QID 1 timeout, aborting
[18795.127566] nvme nvme0: I/O 663 (I/O Cmd) QID 3 timeout, aborting
[18795.133851] nvme nvme0: I/O 664 (I/O Cmd) QID 3 timeout, aborting
[18825.840564] nvme nvme0: I/O 868 QID 1 timeout, reset controller
[18825.877425] nvme0n1: I/O Cmd(0x2) @ LBA 34614208, 512 blocks, I/O Error (sct 0x3 / sc 0x71)
[18825.886001] I/O error, dev nvme0n1, sector 34614208 op 0x0:(READ) flags 0x80700 phys_seg 63 prio class 2
[18825.908586] nvme nvme0: Abort status: 0x371
[18825.912869] nvme nvme0: Abort status: 0x371
[18825.917141] nvme nvme0: Abort status: 0x371
[18825.940624] nvme 0000:01:00.0: enabling device (0000 -> 0002)
[18825.948532] nvme nvme0: Device not ready; aborting initialisation, CSTS=0x0
| 00:24:42 |
| raitobezarius | this makes it impossible to use it without reboot all the time | 00:24:47 |
| raitobezarius | did anyone measured their board energy consumption? | 02:44:50 |
| raitobezarius | it seems like mine does not go above 3.5W | 02:44:57 |
| Alex | In reply to @raitobezarius:matrix.org
it seems like mine does not go above 3.5W USB-PD issue? Maybe try another power supply?
I had microSD disk corruption issues until I stopped using 5V USB. I have no idea how much power is in use now. | 05:03:23 |
 misuzu | In reply to @raitobezarius:matrix.org
it seems like mine does not go above 3.5W Mine draws 4-5W, I have 65W PD power supply and type-c cable with power meter | 06:21:39 |
| misuzu | My nvme is LRC10Z250GG8 | 06:22:35 |
| [0x4A6F] | In reply to @raitobezarius:matrix.org
did anyone measured their board energy consumption? Highest readout while compiling LLVM over an PoE-Splitter on my Switch on port 10 and idle on port 12 (on sdcard, no peripherals):
Local Port PD Class Power Used [W] Current Used [mA] Priority Port Status
10 4 6.673 132 High PoE ON
12 4 4.839 96 High PoE ON
| 14:56:16 |
| raitobezarius | Wow this is really high power | 17:07:11 |
|  Alyssa Ross joined the room. | 20:09:21 |
|  tau joined the room. | 20:11:00 |
| tau | hi ! I just got my riscv SBC ! I'm really excited to help ! | 20:17:48 |
|  shu9 joined the room. | 20:18:59 |
| Alex | In reply to @0x4a6f:matrix.org
Highest readout while compiling LLVM over an PoE-Splitter on my Switch on port 10 and idle on port 12 (on sdcard, no peripherals):
Local Port PD Class Power Used [W] Current Used [mA] Priority Port Status
10 4 6.673 132 High PoE ON
12 4 4.839 96 High PoE ON
Is this at 1GHz or 1.5GHz? | 20:27:52 |
| 8 Aug 2023 |
| misuzu | https://github.com/starfive-tech/VisionFive2/releases/tag/VF2_v3.4.5
Please do not upgrade u-boot/spl for 8GB DDR VisionFive2 since CMA will not allocated successfully under Debian image 202306;
Ok
| 15:43:16 |
| misuzu | * https://github.com/starfive-tech/VisionFive2/releases/tag/VF2_v3.4.5
Please do not upgrade u-boot/spl for 8GB DDR VisionFive2 since CMA will not allocated successfully under Debian image 202306;
Ok
| 15:43:23 |
| raitobezarius | lol | 15:43:28 |
| tau | huh ?? | 16:28:46 |
| tau | you can't upgrade if you have the 8gb variant ? | 16:29:05 |
| misuzu | Finally compiled latest u-boot with pcie for vf2 | 17:42:21 |
| misuzu | Still broken, haha | 17:42:31 |
| raitobezarius | :') | 17:42:35 |
| misuzu | [ 5.648273] pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0001:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 5.654890] starfive-dwmac 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 5.674813] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[ 5.675396] starfive-dwmac 16040000.ethernet: Enabled L3L4 Flow TC (entries=1)
[ 5.683493] pci 0001:00:00.0: BAR 14: assigned [mem 0x38000000-0x380fffff]
[ 5.690083] starfive-dwmac 16040000.ethernet: Enabled RFS Flow TC (entries=10)
[ 5.697309] pci 0001:01:00.0: BAR 0: assigned [mem 0x38000000-0x38003fff 64bit]
[ 5.704178] starfive-dwmac 16040000.ethernet: TSO feature enabled
[ 5.711409] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 5.718704] starfive-dwmac 16040000.ethernet: Using 40/40 bits DMA host/device width
[ 5.724801] pci 0001:00:00.0: bridge window [mem 0x38000000-0x380fffff]
[ 5.745104] pcieport 0001:00:00.0: PME: Signaling with IRQ 63
[ 5.762376] starfive-dwmac 16030000.ethernet end0: renamed from eth0
[ 5.766832] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 200000Hz, actual 199999HZ div = 512)
[ 5.787949] starfive-dwmac 16040000.ethernet end1: renamed from eth1
[ 5.791348] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 5.801479] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 5.813901] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000040000000890
[ 5.823193] mmc_host mmc1: Bus speed (slot 0) = 204799999Hz (slot req 200000Hz, actual 199999HZ div = 512)
[ 5.828340] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 5.838605] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 5.846216] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 5.854293] hub 1-0:1.0: USB hub found
[ 5.858147] hub 1-0:1.0: 1 port detected
[ 5.864676] hub 2-0:1.0: USB hub found
[ 5.868504] hub 2-0:1.0: 4 ports detected
[ 5.916417] nvme nvme0: pci function 0001:01:00.0
[ 5.921223] nvme 0001:01:00.0: enabling device (0000 -> 0002)
[ 6.190840] usb usb2-port2: over-current condition
[ 6.194808] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 100000Hz, actual 99999HZ div = 1024)
[ 6.250806] mmc_host mmc1: Bus speed (slot 0) = 204799999Hz (slot req 100000Hz, actual 99999HZ div = 1024)
[ 6.410819] usb usb2-port4: over-current condition
[ 6.416380] mmc0: Failed to initialize a non-removable card
[ 13.246815] xhci_hcd 0000:01:00.0: Error while assigning device slot ID: Command Aborted
[ 13.260537] xhci_hcd 0000:01:00.0: Max number of devices this xHCI host supports is 32.
[ 13.268574] usb usb1-port1: couldn't allocate usb_device
[ 16.095163] platform cpufreq-dt: deferred probe pending
[ 66.542814] nvme nvme0: I/O 12 QID 0 timeout, completion polled
Timed out for waiting the udev queue being empty.
kbd_mode: KDSKBMODE: Inappropriate ioctl for device
setfont: KDFONTOP: Inappropriate ioctl for device
starting device mapper and LVM...
waiting for device /dev/disk/by-label/NIXOS_ROOT to appear....[ 127.982824] nvme nvme0: I/O 24 QID 0 timeout, completion polled
[ 127.988842] nvme nvme0: Shutdown timeout set to 10 seconds
...................
Timed out waiting for device /dev/disk/by-label/NIXOS_ROOT, trying to mount anyway.
[ 189.422823] nvme nvme0: I/O 16 QID 0 timeout, completion polled
| 17:42:35 |
| raitobezarius | beautiful | 17:42:41 |
| misuzu | Yeah, still won't boot without efi partition on sd card | 17:44:31 |
